dtoverlays: Add BMP580 family to i2c-sensor

They're supported by the standard BMP280 driver, so only
needed the overlay configuration.

Signed-off-by: Dave Stevenson <[email protected]>

Author: 6by9

arch/arm/boot/dts/overlays/README

@@ -2423,7 +2423,7 @@ Info:   Adds support for a number of I2C barometric pressure, temperature,
 Load:   dtoverlay=i2c-sensor,<param>=<val>
 Params: addr                    Set the address for the ADS7828, ADS7830,
                                 ADT7410, AS73211, AS7331, BH1750, BME280,
-                                BME680, BMP280, BMP380, CCS811, DS1621,
+                                BME680, BMP280, BMP380, BMP58x, CCS811, DS1621,
                                 HDC100X, HDC3020, JC42, LM75, MCP980x,
                                 MPU6050, MPU9250, MS5637, MS5803, MS5805,
                                 MS5837, MS8607, SHT3x or TMP102
@@ -2478,6 +2478,10 @@ Params: addr                    Set the address for the ADS7828, ADS7830,
         bmp380                  Select the Bosch Sensortronic BMP380
                                 Valid addresses 0x76-0x77, default 0x76
 
+        bmp58x                  Select the Bosch Sensortronic BMP580, BMP581,
+                                or BMP585
+                                Valid addresses 0x46-0x47, default 0x46
+
         bno055                  Select the Bosch Sensortronic BNO055 IMU
                                 Valid address 0x28-0x29, default 0x29
 

arch/arm/boot/dts/overlays/i2c-sensor-common.dtsi

@@ -756,6 +756,21 @@
 		};
 	};
 
+	fragment@49 {
+		target = <&i2cbus>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			bmp58x: bmp58x@46 {
+				compatible = "bosch,bmp580";
+				reg = <0x46>;
+				status = "okay";
+			};
+		};
+	};
+
 	fragment@99 {
 		target = <&gpio>;
 		__dormant__ {
@@ -817,6 +832,7 @@
 		ads7828 = <0>,"+46";
 		ads7830 = <0>,"+47";
 		adxl355 = <0>,"+48";
+		bmp58x = <0>,"+49";
 
 		addr =	<&bme280>,"reg:0", <&bmp280>,"reg:0", <&tmp102>,"reg:0",
 			<&lm75>,"reg:0", <&hdc100x>,"reg:0", <&sht3x>,"reg:0",
@@ -830,7 +846,7 @@
 			<&hdc3020>,"reg:0", <&as73211>,"reg:0",
 			<&as7331>,"reg:0", <&adxl345>,"reg:0",
 			<&ads7828>,"reg:0", <&ads7830>,"reg:0",
-			<&adxl355>,"reg:0";
+			<&adxl355>,"reg:0", <&bmp58x>,"reg:0";
 		int_pin = <&int_pins>, "brcm,pins:0",
 			<&int_pins>, "reg:0",
 			<&max30102>, "interrupts:0",