ABS sensor HELLA SEAT ATECA
HELLA ABS sensor
SEAT ATECA catalogue online
HELLA Wheel speed sensor Top SEAT ATECA Models
Sensor ABS SEAT ATECA in brand quality: Top Manufacturers
ABS sensor HELLA SEAT ATECA: review
Top 1 Reviews
Good replacement fitted fast and easy, no errors after fitting
Have you ever bought HELLA products from AUTODOC and do you want to share your experience? Help others make the best choice. Leave your feedback and recommendations
HELLA ABS wheel speed sensor SEAT ATECA of brand quality in our amazing selection
We offer HELLA brand produts in OEM quality. Find the right branded ABS sensor spare part your SEAT ATECA car in our catagory.
HELLA 6PU 012 679-941 ABS sensor
Rear Axle, Active sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 012 039-001 ABS sensor
Front Axle Right, without cable, 2-pin connector, 12V
Sold by AUTODOC
HELLA 6PU 358 216-511 ABS sensor
Front Axle, Hall Sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 358 216-311 ABS sensor
Rear Axle, Hall Sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 358 218-501 ABS sensor
Rear Axle, Hall Sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 358 216-501 ABS sensor
Front Axle, Hall Sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 358 218-351 ABS sensor
Rear Axle Right, without cable, Hall Sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 012 806-371 ABS sensor
Rear Axle, Active sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 010 039-991 ABS sensor
Front Axle Left, without cable, 2-pin connector, 12V
Sold by AUTODOC
HELLA 6PU 012 679-931 ABS sensor
Rear Axle, Active sensor, 2-pin connector
Sold by AUTODOC
HELLA 066029 ABS sensor
Front Axle Right, Inductive Sensor, 2-pin connector, 12V
Sold by AUTODOC
HELLA 6PU 010 039-381 ABS sensor
Rear Axle, Inductive Sensor, 1140 Ohm, 845mm, 12V
Sold by AUTODOC
HELLA 6PU 358 216-291 ABS sensor
Hall Sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 358 218-141 ABS sensor
Hall Sensor, 2-pin connector
Sold by AUTODOC
HELLA 6PU 358 218-131 ABS sensor
Hall Sensor, 2-pin connector
Sold by AUTODOC
HELLA abs sensor for SEAT ATECA: top must-read articles
HELLA ABS sensor: What is the price of this product for the SEAT ATECA?
The price of HELLA products in the category ABS sensor for the SEAT ATECA ranges from £8.00 to £41.00, depending on the features and specifications.
faq
DIY repair is only possible if the ABS malfunction is caused by faulty wheel speed sensors. Due to their location, they are highly exposed to moisture and dirt and therefore often fail. In some cases, it is enough to clean the sensitive element with a dry soft lint-free cloth. If this doesn’t work, replace the component.
If a malfunction of the anti-lock braking system is caused by a failure of the electronic control unit or a hydraulic unit, you will need professional assistance. Visit a car repair shop.
First, inspect the component. Cracks on its housing, torn and oxidised wires, and a damaged connector indicate a malfunction.
Use a multimeter for thorough diagnostics. Before you start testing the component, check how the wheel speed sensors are installed in your car. You can find this information in the vehicle repair manual.
You will need to raise the car and most likely to remove the wheel in order to access the part. Next, disconnect the wire from the ABS control unit. Connect the multimeter probes to the sensor contacts and measure resistance. Compare the received values with nominal data – they are usually specified in the car owner’s manual. As a rule, these values vary within the range of 0,5–2,0 kiloohms.
The next step of testing is measuring the voltage on the sensor contacts. To do this, rotate the wheel with your hand at a frequency of about 1 cycle per second. With this frequency, the voltage should be 0,25–0,50 V.
This procedure is determined by the vehicle make and model. Typically, the steps are the following:
- Engage the parking brake and secure the axle opposite to the one on which you’re going to replace the component with wheel chocks. Raise the car.
- Remove the wheel.
- Unscrew the fasteners of the brake caliper, pull it aside and secure with a wire.
- Remove the brake pads and a disc.
- Unscrew the sensor fastening bolt and remove the component from its mounting seat.
- Disconnect the wire from the ABS control unit and car body.
- Install a new part by following all steps in reverse order.
Confidence in online shopping! You can return HELLA abs sensor for SEAT ATECA without explanation within 200 days after purchase and get your money back. How? Just use the Safe Order service at the checkout page. The service cost is only £3.95.
Each order from £2,000.00 value of goods, include free shipping within Great Britain.
*Does not apply to large-size auto parts.
*Except/excluding areas with the following postcodes: GY#####, JE#####, IM#####
