To get the latest status of each upstreaming patch series, please visit our RVspace.
https://rvspace.org/en/project/JH7110_Upstream_Plan
| Component | Test Result | Note |
|---|---|---|
| Clock tree / Reset | Pass | |
| Pinctrl | Pass | |
| Watchdog | Pass | |
| Timer | Pass | |
| PLL clock | Pass | |
| Temperature sensor | Pass | |
| DMA | Pass | |
| PWM | Pass | |
| GMAC | Pass | |
| SDIO / EMMC | Pass | |
| I2C | Pass | |
| SPI | Pass | |
| QSPI | Pass | |
| USB | Pass | |
| PCIe | Pass | Please use a power supply with strong driving capability |
| PMU | Pass | |
| Hibernation | Pass | |
| PMIC | Pass | |
| CPU freq scaling | Pass | |
| Crypto | Fail | Report trace errors at startup |
| TRNG | Pass | |
| PWMDAC | Pass | |
| I2S | Pass | |
| TDM | Pass | |
| HDMI / DC8200 | Pass | But you need to boot Linux with the U-Boot in the mainline |
| MIPI CSI | Pass | |
| ISP | Pass | |
| MIPI CSI PHY | Pass |
- Configure Kconfig options
# Use the modified riscv default defconfig
make ARCH=riscv CROSS_COMPILE=riscv64-linux-gnu- defconfigor
# Select options manually
make ARCH=riscv CROSS_COMPILE=riscv64-linux-gnu- nconfigTo boot up the VisionFive 2 board, please make sure SOC_STARFIVE, CLK_STARFIVE_JH7110_SYS, PINCTRL_STARFIVE_JH7110_SYS, SERIAL_8250_DW are selected.
If you need MMC and GMAC drivers, you should also select MMC_DW_STARFIVE and DWMAC_STARFIVE.
- Build
make ARCH=riscv CROSS_COMPILE=riscv64-linux-gnu-- Power on, enter u-boot and set enviroment parameters
setenv fdt_high 0xffffffffffffffff; setenv initrd_high 0xffffffffffffffff;
setenv scriptaddr 0x88100000; setenv script_offset_f 0x1fff000; setenv script_size_f 0x1000;
setenv kernel_addr_r 0x84000000; setenv kernel_comp_addr_r 0x90000000; setenv kernel_comp_size 0x10000000;
setenv fdt_addr_r 0x88000000; setenv ramdisk_addr_r 0x88300000;
- Set IP addresses for the board and your tftp server
setenv serverip 192.168.w.x; setenv gatewayip 192.168.w.y; setenv ipaddr 192.168.w.z; setenv hostname starfive; setenv netdev eth0;
- Download dtb, image and ramdisk to DDR from your tftp server
tftpboot ${fdt_addr_r} jh7110-starfive-visionfive-2-v1.3b.dtb; tftpboot ${kernel_addr_r} Image.gz; tftpboot ${ramdisk_addr_r} initramfs.cpio.gz;
If your VisionFive 2 is v1.2A, you should download jh7110-starfive-visionfive-2-v1.2a.dtb instead.
- Load and boot the kernel
booti ${kernel_addr_r} ${ramdisk_addr_r}:${filesize} ${fdt_addr_r};
When you see the message "buildroot login:", the launch was successful. You can just input the following accout and password, then continue.
buildroot login: root
Password: starfive